Rebar Calculator

A 24 × 24 ft garage slab with #4 rebar on an 18-inch grid needs 43 twenty-foot sticks, about 860 linear feet including laps, plus 77 chairs to hold the steel up. Enter your slab and spacing to get your own count.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(feet)
feet
(feet)
feet
(inches)
inches

Total 20-Foot Rebar Sticks

73 Sticks (#4 Grade 60 Rebar)

Total Grid Linear Footage

1,443 lin ft (inc. 12% lap splices & trim)

Want a real price for this rebar calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
#4 (0.500") ASTM A615 Grade 60 Rebar7320-Ft SticksProvides 18" on-center two-way grid with 15" lap splices
Heavy-Duty Snap-Lock Rebar Chairs / Dobies128Support ChairsMaintains 2" to 3" clearance off subgrade at slab mid-depth
16-Gauge Black Annealed Tie Wire (3-lb Spool)33-lb SpoolsFor tying intersections in grid matrix

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$1,149 – $1,379

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$1,659 – $3,175

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,153

Average trade labor savings if executed as a skilled DIY homeowner project.

ACI 318 Two-Way Reinforcement Grid Mathematical Model

Rendering formula...

Reinforcement Grid Derivation for 40' × 24' (18" OC Grid)

  1. Runs along Length (40 ft): floor((23.5 × 12) / 18) + 1 = 16 parallel runs.
  2. Runs along Width (24 ft): floor((39.5 × 12) / 18) + 1 = 27 parallel runs.
  3. Net linear footage = (16 × 40') + (27 × 24') = 1,288 lin ft.
  4. Adding 12% for 30-diameter overlap splices and ends: 1288 × 1.12 = 1,443 lin ft.
  5. Dividing by 20 ft commercial stick length: 1443 / 20 = 73 sticks.
Tip: Ensure rebar is suspended on chairs prior to concrete placement; pulling rebar up with hooks is prohibited by ACI 318.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

SlabGrid & BarLinear Feet (with 12% laps)20-Ft SticksChairs
12 × 12 ft24" on center, #3161 lin ft9 sticks20 Support Chairs
20 × 20 ft18" on center, #4627 lin ft32 sticks54 Support Chairs
24 × 24 ft18" on center, #4860 lin ft43 sticks77 Support Chairs
40 × 30 ft16" on center, #42,038 lin ft102 sticks160 Support Chairs
50 × 20 ft12" on center, #52,240 lin ft112 sticks134 Support Chairs
ACI 318 Section 25.5 (Splice & Development Lengths)

ACI 318-19 Building Code Requirements for Structural Concrete

Requires minimum 3-inch concrete cover for reinforcement cast against and permanently exposed to earth. Lap splices must maintain minimum Class B lap length of 30 to 36 bar diameters (15 inches minimum for Grade 60 #4 bar).

How to use the rebar calculator

  1. Enter the slab's length and width in feet.
  2. Pick the grid spacing and bar size from your plans.
  3. Enter the edge clearance in inches. The result shows sticks, linear feet, chairs and tie wire.

How do I calculate rebar for a slab?

Work out how many bars run each way: the slab width (less the edge clearance) divided by the spacing, plus one. Multiply each set by its bar length, add the two together, then add for laps and offcuts. Our calculator adds 12% and divides by 20 ft sticks.

SlabSpacingBarLinear feet20 ft sticksChairs
Patio, 12 × 12 ft24"#3161920
Garage, 24 × 24 ft18"#48604377
Workshop, 30 × 40 ft16"#42,038102160
Heavy apron, 20 × 50 ft12"#52,240112134

What spacing should rebar be in a slab?

Spacing and bar size come from the slab's design and your local code, not from a calculator. Tighter spacing and bigger bars carry more load, which is why the heavy apron above uses #5 bars at 12 inches. If you don't have plans, ask your building department or a contractor what they require for your slab.

How much does rebar for a slab cost?

For the 24 × 24 ft garage slab, our calculator estimates $682 to $818 for the bars, chairs and tie wire, or $989 to $1,892 with a crew placing and tying it.

Frequently asked questions

Why does rebar need chairs?

Chairs hold the steel up inside the concrete instead of letting it lie on the ground, where it does little. Our calculator counts about one chair for every 7.5 sq ft of slab.

Is wire mesh enough instead of rebar?

Mesh is common in thin patios and walks. Driveways, garage floors and slabs that carry heavy loads usually call for rebar. Follow your plans or local requirements.

Does this calculator work for footings?

It's built for a flat grid in a slab. Footings use continuous bars along the trench; our concrete footing calculator handles the concrete for those.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.