24×24 Garage Slab Cost Calculator

A 24 × 24 ft garage slab, 4 inches thick, takes 7.8 cubic yards of concrete (order 8) and costs about $4,900 to $7,400 installed. Going to 6 inches raises the order to 12 cubic yards.

Free · No sign-up · Last reviewed

Quick start:

Your project size

Total Ready-Mix Concrete Required

7.82 Cubic Yards (Order 8.0 yd³)

Pre-Mix 80-lb Bag Equivalent

352 Bags (4000 PSI Air-Entrained)

Want a real price for this 24×24 garage slab co t calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
4000 PSI Ready-Mix Air-Entrained Concrete8.0Cubic YardsIncludes 10% subgrade variance & spillage
#4 (1/2") Deformed Steel Rebar (18" o.c. grid)4720-Ft Sticks939 lin ft (627 lbs) with 15" lap splices
#57 Crushed Stone Base (4" compacted depth)11.9Tons15% mechanical compaction allowance included
10-Mil Heavy Duty Polyethylene Vapor Barrier663Square FeetASTM E1745 Class A puncture resistance
3-Inch Concrete Rebar Support Chairs58ChairsEnsures steel is suspended in upper third of slab
Pre-molded Asphalt Expansion Joint Strip96Linear FeetIsolates slab from adjacent foundation walls

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$2,817 – $3,410

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$4,896 – $7,373

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$3,021

Average trade labor savings if executed as a skilled DIY homeowner project.

24×24 Slab Geometry & Bag Conversion Formula

Rendering formula...

Engineering Math for 24' × 24' (4" Slab at 4000 PSI)

  1. Slab Area = 24 ft × 24 ft = 576 sq ft.
  2. Center Slab Volume = 576 sq ft × (4 ÷ 12 ft) = 192.0 cu ft (7.11 yd³).
  3. Control Joint Cut Quadrants: Four 12' × 12' panels cut to depth of 1".
  4. Total Net Concrete = 7.11 yd³. Factoring 10% subgrade waste = 7.82 yd³ (Dispatch order: 8.0 yards).
  5. Rebar Calculation: 17 runs × 24 ft + 17 runs × 24 ft = 939 linear feet (#4 rebar = 627 lbs).
  6. Sub-base Gravel (4" depth): 7.11 yd³ × 1.45 tons/yd³ × 1.15 compaction = 11.9 tons.
Tip: Under National Average conditions, control joints must be saw-cut within 12 hours of pouring to prevent random shrinkage cracking. Concrete test cylinders should achieve 4000 PSI at 28-day cure.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

ThicknessVolume (Net)Order With 10% Waste80-lb Bag EquivalentTurnkey Contractor Cost Range
4 Inches7.11 yd³7.82 Cubic Yards352 Bags$4,900 – $7,400
5 Inches8.89 yd³9.78 Cubic Yards440 Bags$5,200 – $7,800
6 Inches10.67 yd³11.74 Cubic Yards528 Bags$5,500 – $8,200
4" Slab + 12" Edge10.43 yd³11.47 Cubic Yards516 Bags$7,200 – $10,500
ACI 302.1R Guide for Concrete Floor Construction

ACI 302.1R Joint Spacing & Compressive Strength

A 24x24 slab must have control joints cut into 4 equal quadrants (12' × 12' panels) at a depth of 1/4 the slab thickness (1" deep for a 4" slab) within 12 hours of pouring. Concrete mix design must be minimum 3,500 to 4,000 PSI with air entrainment.

How to use the garage slab cost calculator

  1. Choose the slab thickness: 4 inches for cars, 5 for heavy trucks, 6 for a car lift or equipment.
  2. Choose the reinforcement: a #4 rebar grid, welded wire mesh or synthetic fibers.
  3. Read the concrete to order and the materials list, and compare the contractor range with your quotes. This page is for a 24 × 24 ft slab. For other sizes use the concrete cost calculator.

How much concrete for a 24×24 garage slab?

Multiply 24 × 24 ft by the thickness in feet and divide by 27. At 4 inches that is 576 sq ft × 0.333 ft = 192 cubic feet = 7.11 cubic yards. Add 10% for uneven ground and spillage and you get 7.82 cubic yards, which you order as 8.

ThicknessNet volumeOrder with 10% waste80-lb bag equivalentInstalled cost range
4 in7.11 cu yd7.82 (order 8.0)352$4,900 – $7,400
5 in8.89 cu yd9.78 (order 10.0)441$5,200 – $7,800
6 in10.67 cu yd11.73 (order 12.0)528$5,500 – $8,200

The installed range is a national average for a contractor to prep, form, place and finish. It does not include a permit, extensive grading, or a thickened edge. A real quote will differ with your site and local prices.

How thick should a garage slab be?

The model residential code sets 3.5 inches as the minimum for slabs on ground, and 4 inches is the common choice for a garage used by cars. Go to 5 or 6 inches if you park heavy trucks, add a two-post car lift or store equipment. The extra inch costs about 2 cubic yards on this size of slab. Our guide on garage slab thickness covers when it is worth it.

Rebar, wire mesh or fibers: what does each add?

The calculator changes the materials list for each choice:

ReinforcementWhat the list shows (4 in, 24 × 24 ft)
#4 rebar grid, 18 in centers47 twenty-foot sticks and 58 chairs
Welded wire mesh 6×613 sheets of 5 × 10 ft, with laps, and 58 chairs
Synthetic fibersDosed into the concrete at the plant, with no steel to place

Whichever you choose, the steel needs to sit in the upper part of the slab, which is what the chairs are for. Fibers are mixed in and follow the maker's dosage. Plans and your inspector decide what is required.

Frequently asked questions

How many bags of concrete for a 24×24 slab?

About 352 bags of 80-lb mix for a 4-inch slab. That is not a one-person job: bagged concrete starts to set long before you have mixed that many batches. Order ready-mix and have help for placing and finishing.

What goes under the slab?

The materials list includes 4 inches of compacted #57 crushed stone and 10-mil polyethylene sheeting. Garage slabs are often exempt from the vapor retarder rule in some states, so check what your building department requires. Joint strips go around the edge to separate the slab from the walls.

Where should control joints go?

Cutting the slab into four 12 × 12 ft panels, about one-quarter of the slab thickness deep, is the usual layout for a 24 × 24 ft slab. Cut within about 12 hours of the pour, as soon as the concrete will take a saw without raveling.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.