Concrete Block Calculator

A 30 ft long, 8 ft high wall of 8×8×16 concrete block covers 240 sq ft and takes 284 blocks, 9 bags of Type S mortar and about 0.7 cubic yards of core-fill grout when every 32 inches is grouted.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(ft)
ft
(ft)
ft

Total 8×8×16 CMU Blocks Required

213 Blocks (180 sq ft wall face)

Type S Mortar & Grout Fill

7 Bags Mortar | 0.5 yd³ Core Fill

Want a real price for this concrete block calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
Standard 8×8×16 Lightweight CMU Blocks213BlocksIncludes 5% cutting and corner waste
Type S Masonry Cement (80-lb bags)7BagsMixed at 1 part cement to 2.5 parts masonry sand
Fine Washed Masonry Sand0.7TonsClean aggregate for smooth 3/8-in bed and head joints
Coarse Core-Fill Grout (2,500 PSI)0.5Cubic YardsConsolidates rebar cells per NCMA structural specs
#4 (1/2-in) Deformed Rebar for Vertical Cores24PiecesVertical dowels embedded into foundation footing

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$738 – $893

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$3,240 – $5,040

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$3,325

Average trade labor savings if executed as a skilled DIY homeowner project.

Standard CMU Face Area & Mortar Formula

Rendering formula...

Masonry Estimation for 30' Long × 6' High Block Wall

  1. Wall Face Area = 30 ft × 6 ft = 180 sq ft.
  2. Block Count Formula = 180 sq ft × 1.125 blocks/sq ft × 1.05 waste factor = 213 blocks.
  3. Mortar Requirement: 213 blocks ÷ 100 × 3.0 bags = 7 bags Type S mortar.
  4. Core-Fill Grout: Vertical rebar cells consolidated with 0.5 cubic yards of high-slump structural grout.
Tip: In National Average, structural block walls over 4 feet require vertical rebar every 32 inches and horizontal ladder wire every second course.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Wall Length × HeightCourses High8×8×16 CMU BlocksType S Mortar (80-lb Bags)Turnkey Masonry Contractor Price
20 ft × 4 ft (80 sq ft)6 Courses95 Blocks3 Bags$1,600 – $2,400
30 ft × 6 ft (180 sq ft)9 Courses213 Blocks7 Bags$3,600 – $5,400
40 ft × 8 ft (320 sq ft)12 Courses378 Blocks12 Bags$6,400 – $9,600
60 ft × 8 ft (480 sq ft)12 Courses567 Blocks18 Bags$9,500 – $14,400
ASTM C90 Loadbearing Concrete Masonry Units / TMS 402 Building Code

ASTM C90 & TMS 402/602 Masonry Standards

Concrete masonry walls must be built upon a poured concrete footing below the frost line at twice the width of the block (16" wide for 8" CMU). Type S mortar (1,800 PSI minimum) is mandatory for at-or-below grade retaining and structural walls.

How to use the concrete block calculator

  1. Enter the wall's length and height in feet.
  2. Pick the block width: 6, 8 or 12 inches.
  3. Pick how often the cores are grouted. The result shows blocks, mortar, sand, grout and rebar.

How many concrete blocks do I need?

A standard 8×16 block face covers 0.889 sq ft once the mortar joint is included, which is 1.125 blocks per square foot (derived: 144 ÷ 128). Our calculator multiplies the wall area by 1.125 and adds 5% for breakage and cuts.

WallFace areaBlocksMortar (80-lb bags)Core-fill grout
Garage stem wall, 24 × 3 ft72 sq ft8630.2 cu yd
Retaining wall, 40 × 4 ft160 sq ft18960.4 cu yd
Basement wall, 30 × 8 ft240 sq ft28490.7 cu yd

How much mortar do I need for block?

Our calculator uses 3 bags of Type S mortar per 100 blocks, plus about 0.9 tons of masonry sand for the 284-block wall. Mixing by the batch as you go keeps the mortar workable.

How much grout do I need to fill block cores?

It depends on how many cores you fill. Grouting only the cores with rebar, every 32 or 48 inches, uses far less than filling every cell. The basement wall above needs about 0.7 cubic yards with cores grouted every 32 inches.

Frequently asked questions

What does a concrete block wall cost?

For the 30 × 8 ft basement wall, our calculator estimates $4,320 to $6,720 for a mason, or $978 to $1,184 in materials.

Do I need rebar in a block wall?

Most foundation and retaining walls are reinforced, with vertical bars grouted into the cores. The bar size and spacing come from your plans or local code; our calculator includes an estimated count of #4 bars.

How many blocks are on a pallet?

It varies by plant and block weight; ask your supplier.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.