French Drain Calculator

A 50 ft French drain in a trench 12 inches wide and 24 inches deep takes about 5.9 tons of #57 drainage stone, 50 ft of perforated pipe and 300 square feet of filter fabric. The trench should fall 6.3 inches from the high end to the outlet.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(ft)
ft
(in)
in
(in)
in

Crushed Drainage Stone Tonnage

5.2 Tons #57 Washed Gravel (3.1 yd³)

Trench Drop & Geotextile Fabric

7.5" Elevation Drop (1% Slope) | 288 sq ft Fabric

Want a real price for this french drain calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
#57 Washed Angular Drainage Stone5.2Compacted Tons15% mechanical settlement allowance included
Perforated 4" SDR-35 or Corrugated Pipe60Linear FeetHoles oriented downward at 4 and 8 o'clock
Non-Woven Geotextile Filter Fabric (4-oz)288Square FeetWraps entire gravel envelope to prevent silt clogging
Pop-Up Emitter with Surface Grate1Discharge KitDaylight discharge terminal away from property lines

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$471 – $570

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$1,920 – $2,880

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,880

Average trade labor savings if executed as a skilled DIY homeowner project.

French Drain Volume & Minimum Slope Hydraulics

Rendering formula...

Drainage Math for 60' Trench (12"W × 18"D) with 4" Pipe

  1. Trench Excavation Volume = 60' × 1.00' × 1.50' = 90.0 cu ft.
  2. Perforated Pipe Displacement = π × (0.167')² × 60' = 5.2 cu ft.
  3. Net Gravel Void = (90.0 - 5.2) ÷ 27 = 3.14 cubic yards.
  4. Stone Weight = 3.14 yd³ × 1.45 tons/yd³ × 1.15 compaction = 5.2 tons #57 stone.
  5. Required Trench Slope: 1/8" drop per foot × 60' = 7.5 inches total elevation fall.
Tip: In National Average, always place holes face-DOWN. Water rises from the subgrade into the pipe from below, maintaining gravity discharge.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Drain LengthRequired Drop (1% Slope)#57 Crushed Stone NeededGeotextile Fabric NeededContractor Installation Price
30 ft3.75 inches drop2.2 Tons (1.6 yd³)30 ft (5-ft roll)$1,800 – $2,700
60 ft7.50 inches drop4.4 Tons (3.1 yd³)60 ft (5-ft roll)$3,600 – $5,200
100 ft12.5 inches drop7.3 Tons (5.2 yd³)100 ft (5-ft roll)$5,900 – $8,500
150 ft18.75 inches drop11.0 Tons (7.8 yd³)150 ft (5-ft roll)$8,800 – $12,800
ASTM D4751 (Apparent Opening Size) / ASTM D4632

Geotextile Separation & Civil Soil Standards

French drains must be lined with 4-oz or 6-oz non-woven geotextile filter fabric. Never use woven weed barrier fabric, which clogs with silt. Perforations on the drain pipe must point downward toward the gravel bedding to prevent sediment infiltration.

How to use the french drain calculator

  1. Enter the trench length in feet, and the width and depth in inches.
  2. Choose the pipe diameter, 4 inches for most yards or 6 inches for larger flows.
  3. Read the stone, pipe, fabric and the total drop the trench needs, then compare the contractor range with your quotes.

How much gravel do I need for a French drain?

Find the trench volume (length × width × depth), subtract the volume the pipe takes up, divide by 27 for cubic yards, then convert to tons. Our calculator uses 1.45 tons per cubic yard of washed #57 stone and adds 15% for settling.

Trench = Length (ft) × Width (ft) × Depth (ft)
Pipe = π × (Diameter ÷ 2)² × Length
Stone (cu yd) = (Trench − Pipe) ÷ 27
Tons = Stone × 1.45 × 1.15

For a 50 ft trench, 12 in wide and 24 in deep, with a 4 in pipe: 100 cu ft − 4.4 cu ft = 95.6 cu ft = 3.54 cu yd, × 1.45 × 1.15 = 5.9 tons.

DrainTrenchPipeStoneFabricTotal drop
Foundation footing drain, 50 ft12 × 24 in4 in5.9 tons300 sq ft6.3 in
Yard drain, 80 ft12 × 16 in4 in6.2 tons352 sq ft10.0 in
Driveway swale, 100 ft18 × 20 in6 in14.2 tons580 sq ft12.5 in

What slope does a French drain need?

The pipe must fall toward the outlet so water keeps moving. NDS recommends a drop of at least 1 percent, and a 2 percent minimum for corrugated pipe. Our calculator uses one-eighth of an inch per foot, which is about 1 percent, so a 50 ft drain falls 6.3 inches. Use the percentage your pipe maker and local rules call for. Check the fall along the whole run and not only at the ends, because a dip holds water and silt.

How wide and deep should a French drain trench be?

NDS says a trench 5 to 6 inches wide can handle smaller drainage problems and that 8 inches to 2 feet deep is enough for many water-diverting projects, while foundation or retaining wall drains may need to go deeper. The calculator defaults to 12 inches wide and 24 inches deep, which is a typical size for a foundation drain. Wider and deeper trenches carry more water but cost more stone and digging.

What else goes in a French drain?

The calculator's materials list covers the stone, perforated pipe, non-woven filter fabric around the stone, and a pop-up emitter to discharge the water. NDS notes that the fabric stops soil from mixing with the gravel and keeps water flowing through, and that the pipe has to lead to an outlet that drains away from the house. Plan where the water leaves the drain before you dig.

Frequently asked questions

How much does a French drain cost?

For the 50 ft example, the calculator shows about $485 to $587 in materials for a DIY job and $1,600 to $2,400 with a contractor, at national averages. Cost rises with depth, access, rock and the need to tie into a storm line. Our French drain cost guide goes into the price in detail.

Should the pipe have holes up or down?

Follow the pipe maker's instructions. Practice varies by product, and the calculator's materials note describes the common layout for the pipe it lists. Always lay perforated pipe with a continuous fall to the outlet.

Can a French drain be too long?

Long runs need enough total fall, and the calculator shows it: 100 ft needs 12.5 inches. If the site does not have that much slope, a longer drain may need to be deeper at the outlet end or discharge in sections. Ask a drainage contractor when the numbers do not fit.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.