Paver Calculator

A 16 × 12 ft patio of 4 × 8 inch pavers needs about 951 pavers, 4.0 tons of crushed stone base, 0.8 tons of bedding sand and 3 bags of polymeric joint sand. The paver count includes 10% for cuts and border waste.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(ft)
ft
(ft)
ft

Total Interlocking Paver Count

1,486 Pavers (300 sq ft Patio)

Compacted Base & Bedding Sand

6.2 Tons Crushed Stone | 1.3 Tons Sand

Want a real price for this paver calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
Concrete Interlocking Pavers (4×8 in)1,486PaversIncludes 10% perimeter cutting and border waste
Crushed Stone Base Aggregate (4" depth)6.2TonsCompacted with vibratory plate in 2-in lifts
Coarse Washed Concrete Bedding Sand (1-in depth)1.3TonsScreeded uncompacted ASTM C33 concrete sand
Polymeric Joint Sand (50-lb bags)4BagsSwept into joints and water-activated to prevent weeds
Snap-Edge Paver Restraints & 10-in Spikes70Linear FeetLocks perimeter pavers against lateral shifting

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$1,781 – $2,156

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$4,350 – $7,200

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$3,807

Average trade labor savings if executed as a skilled DIY homeowner project.

ICPI Multi-Layer Aggregate & Sand Formula

Rendering formula...

Hardscape Foundation Math for 20' × 15' Paver Patio

  1. Patio Area = 20 ft × 15 ft = 300 sq ft.
  2. Crushed Stone Sub-Base (4" depth): (300 × 0.3333333333333333') ÷ 27 × 1.45 tons/yd³ × 1.15 compaction = 6.2 tons.
  3. Bedding Sand Layer (1" depth): (300 × 0.083') ÷ 27 × 1.35 tons/yd³ = 1.3 tons.
  4. Paver Count: 300 sq ft × 4.5 pavers/sq ft × 1.10 waste factor = 1,486 pavers.
  5. Polymeric Sand: 300 sq ft ÷ 75 sq ft/bag = 4 bags.
Tip: In National Average, never use masonry sand or stone dust for your 1" bedding layer—it traps water and causes paver heaving. Use ASTM C33 coarse concrete sand.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Patio Area4" Base Stone (Tons)1" Bedding Sand (Yards)50-lb Polymeric Sand BagsTurnkey Contractor Price
10' × 12' (120 sq ft)2.8 Tons0.40 yd³2 Bags$2,200 – $3,400
15' × 20' (300 sq ft)6.8 Tons0.93 yd³5 Bags$5,400 – $8,100
20' × 25' (500 sq ft)11.3 Tons1.54 yd³8 Bags$8,900 – $13,500
25' × 35' (875 sq ft)19.8 Tons2.70 yd³13 Bags$15,500 – $23,500
Interlocking Concrete Pavement Institute (ICPI) Tech Spec 2

ICPI Tech Spec #2 & Joint Sand Activation

Bedding sand must be ASTM C33 washed concrete sand, never limestone screenings or stone dust (which wash away). Polymeric sand must be misted with water in 3 light passes without flooding to activate polymers and prevent hazing.

How to use the paver calculator

  1. Enter the patio length and width in feet.
  2. Pick the paver size and the depth of the crushed stone base. Patios and walkways usually use 4 to 6 inches.
  3. Read the paver count, base stone, bedding sand and joint sand, then compare the contractor range with your quotes.

How many pavers do I need for a patio?

Multiply the patio area in square feet by the number of pavers per square foot, then add 10% for cuts and the border. A 4 × 8 inch paver covers 32 square inches, so it takes 4.5 pavers per square foot. A 6 × 6 paver takes 4, and a 12 × 12 takes 1.

Pavers = Area (sq ft) × Pavers per sq ft × 1.10

For a 16 × 12 ft patio: 192 sq ft × 4.5 × 1.10 = 951 pavers.

PatioPaverPavers to buyBase stoneBedding sandJoint sand
16 × 12 ft4 × 8 in9514.0 tons (4 in)0.8 tons3 bags
16 × 12 ft6 × 6 in8454.0 tons (4 in)0.8 tons3 bags
20 × 15 ft12 × 12 in3309.3 tons (6 in)1.3 tons4 bags
20 × 20 ftashlar pattern1,9818.2 tons (4 in)1.7 tons6 bags
35 × 4 ft walkway4 × 8 in6932.9 tons (4 in)0.6 tons2 bags

Ashlar sets mix several sizes, and the pieces per square foot vary by product. We use 4.5 per square foot as a rough figure. Buy ashlar patterns by the square foot of coverage printed on the pallet.

How much base stone and sand does a paver patio need?

Belgard's installation guidance says a walkway or patio needs 4 to 6 inches of compacted crushed stone base, with about 1 inch of bedding sand spread over it. Driveways need roughly twice as much base. Our calculator works out the stone as area × depth, with a 15% allowance for compaction, at 1.45 tons per cubic yard. The sand is a 1-inch layer at 1.35 tons per cubic yard.

For the 16 × 12 ft patio at 4 inches of base: 192 sq ft × 0.333 ft ÷ 27 × 1.45 × 1.15 = 4.0 tons of stone. The sand layer is 192 × 0.083 ÷ 27 × 1.35 = 0.8 tons.

Use a thicker base, 6 inches, over clay or soft soil and in freezing climates. Belgard also advises compacting the stone in lifts of no more than 4 to 6 inches at a time, because a thicker pass does not compact properly.

How much does a paver patio cost?

For the 16 × 12 ft example, the calculator shows about $1,154 to $1,397 in materials for a DIY job and $2,784 to $4,608 with a contractor, a national average. Pavers are most of the material cost, and prices vary by product and region. Edging, a deeper base and site work add to a real quote.

Frequently asked questions

What is polymeric sand and how much do I need?

Polymeric sand is joint sand with a binder that hardens when it is wet. It locks the pavers together and resists weeds and washout. The calculator assumes one 50-lb bag covers about 75 square feet. Follow the bag's instructions for the exact coverage and for how to activate it.

Do I need edge restraints?

Yes. Pavers need a firm edge to keep them from creeping apart over time. Our materials list includes enough plastic edge restraint and spikes to go around the whole perimeter, which is 56 linear feet for the 16 × 12 ft patio.

How deep should the paver base be?

Four to six inches of compacted crushed stone is the usual range for patios and walkways, according to Belgard's installation guide. The calculator offers 4, 6 and 8 inches. Pick 6 inches for clay soil, poor drainage or a freezing climate, and ask a local installer what works in your ground.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.