Brick Calculator

A 12 × 8 ft wall of standard modular brick, one brick thick, takes about 713 bricks, which is two pallets. That counts 6.75 bricks per square foot and adds 10% for cuts and breakage.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(feet)
feet
(feet)
feet
(%)
%

Total Face Bricks Required

1,783 Bricks (4 Pallet Cubes)

Mortar & Sand Requirements

17 Bags Type N/S Mortar + 2 Tons Masonry Sand

Want a real price for this brick calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
MODULAR Facing Bricks1,783BricksCovers 240 sq ft face with 10% cut & bat allowance
Type N / Type S Masonry Cement (70-lb Bags)1770-lb BagsASTM C270 proportioned masonry mortar
Washed Clean Masonry Sand (ASTM C144)2TonsSharp fine sand for structural joint bonding
Galvanized Corrugated Wall Ties90TiesSpaced every 16" vertical × 24" horizontal per BIA code

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$1,844 – $2,213

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$3,600 – $6,240

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$2,892

Average trade labor savings if executed as a skilled DIY homeowner project.

Brick Industry Association (BIA) Area Yield Formula

Rendering formula...

Brick Estimating Derivation for 30' × 8' Wall

  1. Gross Wall Surface Area = 30 ft × 8 ft = 240 sq ft.
  2. Standard modular yield factor with 3/8" mortar joint = 6.75 bricks/sq ft.
  3. Multiplying by 1 wythe(s): 240 × 6.75 × 1 = 1620 base bricks.
  4. Adding 10% cutting and breakage allowance: 1,783 bricks total.
  5. Standard pallets contain 500 bricks = 4 strapping cubes.
Tip: Order all brick cubes from the same kiln firing run to ensure consistent clay color and texture.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Wall Face AreaModular Bricks (Single)King BricksMortar Bags (Type N)Turnkey Mason Cost
50 sq ft372 Bricks316 Bricks4 Bags$750 – $1,350
100 sq ft743 Bricks633 Bricks7 Bags$1,450 – $2,600
250 sq ft1,856 Bricks1,581 Bricks17 Bags$3,600 – $6,500
500 sq ft3,713 Bricks3,163 Bricks34 Bags$7,200 – $13,000
BIA Technical Notes 10B & ASTM C216 Facing Brick

BIA Technical Notes on Brick Construction

Exterior veneer requires ASTM C216 Grade SW (Severe Weathering) brick with Type N mortar for above-grade walls. Corrugated 22-gauge galvanized wall ties must be placed at 2.67 sq ft maximum spacing.

How to use the brick calculator

  1. Enter the length and height of the wall in feet. Subtract window and door openings only if you want a tighter count.
  2. Pick the brick type and whether the wall is one or two bricks thick (wythes).
  3. Keep the 10% waste allowance for a first job, then read the bricks, pallets, mortar and ties.

How many bricks do I need for a wall?

Multiply the wall area in square feet by the number of bricks per square foot, then add 10% for cuts and breakage. A standard modular brick has a nominal face of 8 by 2⅔ inches once the mortar joint is included, which works out to 6.75 bricks per square foot. The Brick Industry Association's Technical Note 10 lists 675 modular brick per 100 square feet of wall with a 3/8 inch joint.

Bricks = Wall area (sq ft) × Bricks per sq ft × Wythes × 1.10

For a 12 × 8 ft wall: 96 sq ft × 6.75 = 648, × 1.10 = 713 bricks.

WallBrickWythesBricks to buyPallets (500)Mortar bags
12 × 8 ft accent wallModular171327
40 × 3 ft garden wallModular21,783417
25 × 10 ft garage facadeKing11,582415
80 × 9 ft house facadeModular15,3461149

How much mortar do I need?

Mortar quantities depend on the joint width and the brick size. BIA's Technical Note 10 gives about 8 cubic feet of mortar per 1,000 modular brick at a 3/8 inch joint. Our calculator turns the brick count into bags of masonry cement at 110 bricks per 70-lb bag, with sand at 0.12 tons per bag. That runs higher than the BIA volume suggests, so treat the bag count as a generous upper estimate and ask your supplier how many bags of their mortar mix cover your brick count.

How many brick sizes does the calculator cover?

It covers four: modular (6.75 per sq ft), king (5.75), queen (6.0) and utility (3.0). Brick sizes vary by maker, so check the face size on your brick's data sheet and the count per square foot it gives. Bricks per square foot is the number to change if your brick is not standard. A two-wythe wall doubles the brick count and the cost.

Frequently asked questions

How many bricks are on a pallet?

The calculator assumes 500 bricks per pallet, which is common for standard modular brick, though the count varies by product and region. Ask your supplier for the pallet count and add the extra pallet if the total falls just over.

Should I subtract windows and doors?

You can. Enter the full wall to get a safe count, or use a smaller wall area for the openings. Brick around openings needs more cutting, so most builders keep the 10% allowance even after subtracting openings.

How many wall ties do I need?

The calculator lists one tie for every 2.67 square feet of wall, which is a spacing of 16 inches vertically by 24 inches horizontally. That tie count is for a veneer or cavity wall. Your plans and local code set the actual spacing and tie type.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.