Tankless Water Heater Size Calculator

Two showers and a sink running at once in a cold climate, with 42°F water coming in, need a tankless heater that delivers 5.5 GPM at a 78°F temperature rise. In gas terms that is about 252,000 BTU of input.

Free · No sign-up · Last reviewed

Quick start:

Your project size

Required Tankless Flow Rate (GPM)

5.5 GPM at 70°F Temp Rise

Gas Input / Electric Demand

226k BTU Gas OR 94 kW Electric

Want a real price for this tankle water heater size calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
Condensing Tankless Gas Water Heater (226k BTU)1UnitDelivers 5.5 GPM at 70°F rise (0.95 UEF)
3/4-in High-Capacity Gas Supply Line1LineEnsures required gas volume without dropping pressure
Concentric Direct Vent Flue Pipe1Vent KitSchedule 40 PVC/polypropylene side-wall vent
Service Isolation Ball Valves1PairRequired for annual vinegar descaling flush

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$1,100 – $1,600

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$2,400 – $3,800

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,750

Average trade labor savings if executed as a skilled DIY homeowner project.

Flow Rate & Thermal Heat Output Formula

Rendering formula...

Hydraulic Math for 2 Showers + 1 Sinks with 50°F Groundwater

  1. Simultaneous Peak Flow Rate = (2 showers × 2.0 GPM) + (1 appliances × 1.5 GPM) = 5.5 GPM.
  2. Temperature Rise (ΔT) = 120°F Target - 50°F Inlet = 70°F rise.
  3. Gas Input Formula = (5.5 GPM × 500 × 70°F) ÷ 0.85 efficiency = 226,471 BTU/hr.
  4. Electric Equivalent = (5.5 × 70°F) ÷ 4.1 = 94 kW (mandates minimum 150A dedicated electric service).
Tip: In National Average, groundwater temps dictate winter heating performance. Choose a unit rated for your winter groundwater low.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Peak FixturesTotal Flow (GPM)Delta T RiseGas BTU / Electric kWInstalled Turnkey Cost
1 Shower2.0 – 2.5 GPM60°F Rise120,000 BTU / 18 kW$2,200 – $3,400
2 Showers4.5 – 5.0 GPM70°F Rise180,000 BTU / 27 kW$3,200 – $4,600
2 Showers + Dishwasher6.0 – 7.0 GPM70°F Rise199,000 BTU / 36 kW$3,800 – $5,400
3 Showers + Washer8.5 – 9.5 GPM75°F RiseCascade Dual 199k BTU$6,500 – $9,200
International Plumbing Code (IPC) / National Fuel Gas Code NFPA 54

IPC Chapter 6 & NFPA 54 Fuel Gas Code

Gas tankless units must be vented with Category III or IV stainless steel or polypropylene pipe. Gas meter delivery pressure must maintain a minimum of 5.0" w.c. for natural gas and 10.5" w.c. for propane under full equipment load.

How to use the tankless water heater calculator

  1. Pick how many showers might run at the same time.
  2. Add the other hot-water fixtures that could be on at that moment, such as a kitchen sink or dishwasher.
  3. Pick your groundwater temperature. The result shows the flow rate, the temperature rise, and the gas or electric size that delivers it.

How many GPM do I need for a tankless water heater?

Add up the hot water that can run at once. Our calculator counts 2.0 GPM per shower and 1.5 GPM per other fixture.

HouseholdPeak flowInlet waterTemperature riseGas input
1 shower2.0 GPM50°F70°Fabout 82,000 BTU
2 showers + 1 fixture5.5 GPM42°F78°Fabout 252,000 BTU
3 showers + 1 fixture7.5 GPM65°F55°Fabout 243,000 BTU

The two bigger homes end up with similar burners: the southern home moves more water but heats it less.

How do I calculate the GPM for a tankless water heater?

Start with peak flow, then work out the temperature rise: the outlet temperature (our calculator uses 120°F) minus your incoming water temperature. A heater's rating only means something at a stated rise, so compare models at your rise, not the headline GPM. Colder inlet water means the same heater delivers fewer gallons per minute.

What size gas tankless do I need?

Gas input = GPM × 500 × temperature rise ÷ efficiency. Our calculator uses 85% efficiency. For 5.5 GPM at a 78°F rise: 5.5 × 500 × 78 ÷ 0.85 = about 252,000 BTU. Many whole-house gas units top out around that size, so a large home in a cold region may need two units.

Frequently asked questions

Is an electric tankless enough for a whole house?

Electric units need very large circuits. Our calculator shows the 2-shower cold-climate home would need about 105 kW, which is beyond many homes' service. Electric tankless works best for one bathroom or as a point-of-use heater.

Why does groundwater temperature matter so much?

The heater has to make up the whole difference between inlet and outlet temperature. Inlet water at 42°F needs a 78°F rise to reach 120°F, while 65°F water needs only 55°F.

What does a tankless water heater cost installed?

Our calculator estimates $2,400 to $3,800 installed for a condensing gas unit, or $1,100 to $1,600 for the unit and parts alone. New gas lines or venting raise the price.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.