Water Pipe Size Calculator

A home with two full bathrooms, one kitchen sink and one hose bibb adds up to 11 water supply fixture units, which our calculator sizes as a 3/4-inch main with 1/2-inch PEX branches. Count your fixtures and it does the rest.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(rooms)
rooms
(rooms)
rooms
(fixtures)
fixtures
(bibbs)
bibbs

Recommended Main Trunk Diameter

1-in Pipe (17.0 Total WSFU Load)

Branch Sizing & Peak Flow Rate

1/2-in PEX Home-Run Branches | 16.3 GPM Peak Demand

Want a real price for this water pipe size calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
PEX-A ProPEX Expansion Pipe (1-in)100FeetSupplies central distribution manifold from water meter
1/2-in PEX Flexible Tubing (Red & Blue)300FeetDedicated runs to each individual plumbing fixture
Copper or Poly Manifold with Ball Valves2ManifoldsDedicated hot and cold home-run isolation banks
Full-Port Brass Ball Valves6ValvesQuarter-turn emergency shutoffs at main and branches

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$450 – $850

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$2,200 – $4,200

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$2,550

Average trade labor savings if executed as a skilled DIY homeowner project.

IPC Water Supply Fixture Unit (WSFU) Sizing Method

Rendering formula...

IPC WSFU Calculation for 2 Full Baths + 1 Half Baths

  1. Full Baths (2 × 3.5 WSFU) = 7.0 WSFU.
  2. Half Baths (1 × 2.0 WSFU) = 2.0 WSFU.
  3. Kitchen Sinks (2 × 1.5 WSFU) + Hose Bibbs (2 × 2.5 WSFU) = 8.0 WSFU.
  4. Total Water Supply Fixture Units = 17.0 WSFU.
  5. Trunk Diameter per IPC Table E103.3: Exceeds 3/4-in capacity (16 WSFU), mandating a 1-in minimum trunk.
Tip: In National Average, PEX-A expansion fittings provide 20% higher flow velocity and freeze-burst immunity compared to crimp PEX-B fittings.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Fixture Score (WSFU)Home TypeRecommended Main TrunkIndividual Fixture BranchesRepipe Contractor Cost
1 – 9.5 WSFU1 to 1.5 Bath Condo3/4" PEX-A Trunk1/2" Branches$3,200 – $5,400
10 – 19 WSFU2 to 2.5 Bath Home3/4" or 1" Trunk1/2" Branches$4,800 – $7,200
20 – 32 WSFU3 to 4 Bath Estate1" PEX-A Main Trunk1/2" & 3/4" Tub Branches$7,500 – $11,500
33+ WSFULuxury Multi-Family1-1/4" Main Supply3/4" Sub-Trunks$12,000 – $18,000
International Plumbing Code Appendix E / ASTM F876 PEX Tubing

IPC Table E103.3 & ASTM F876/F877 Standards

Water velocity in PEX piping must not exceed 8 feet per second for cold water and 5 feet per second for hot water to prevent hydraulic erosion and water hammer. Expansion fittings (PEX-A ProPEX) provide higher flow than insert crimp rings (PEX-B).

How to use the water pipe size calculator

  1. Enter the number of full and half bathrooms.
  2. Enter kitchen sinks and outdoor hose bibbs.
  3. Read the total fixture units, the main trunk size and the peak flow. Have a plumber confirm the size against your local code, pressure and pipe length.

How do I calculate plumbing fixture units?

Each fixture is given a load value, and you add them up. Our calculator uses these values:

FixtureFixture units (our calculator)
Full bathroom3.5
Half bathroom2.0
Kitchen sink1.5
Hose bibb2.5

Two full baths (7.0) plus a kitchen sink (1.5) and a hose bibb (2.5) make 11.0 fixture units.

What size main water line do I need?

Our calculator keeps a 3/4-inch trunk up to 16 fixture units and moves to 1-inch above that.

HomeFixture unitsMain trunkPeak demand
1 bath cottage7.53/4"9.1 GPM
2 full baths11.03/4"11.8 GPM
3 full + 1 half, 2 kitchens20.51"18.9 GPM

Long runs from the meter and low street pressure can push a home to the next size up, which is why the final call belongs to a plumber.

Frequently asked questions

Is 1/2-inch PEX enough for a shower?

For a single fixture on its own home-run line, our calculator uses 1/2-inch branches. The trunk feeding the whole house is what needs to be larger.

What does a PEX repipe cost?

Our calculator estimates $2,200 to $4,200 for a professional manifold system, or $450 to $850 in materials. Opening and patching walls adds to that.

Does water pressure change the pipe size?

Yes. Fixture units estimate demand, but pressure and pipe length decide how much flow actually arrives. Low pressure or a long run from the street can call for a larger main.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.