Recessed Lighting Calculator

A standard 18×14 kitchen with 9-foot ceilings needs 16 recessed LED can lights (800 lumens each, 10,080 total lumens target) arranged in a 4×4 grid spaced 4.5 feet apart and 2.3 feet from walls to achieve a recommended 40 foot-candle illumination level.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(ft)
ft
(ft)
ft

Recommended Can Light Fixture Count

16 Lights LED Cans (12,000 Total Lumens)

Grid Layout & Wall Spacing

5.0' Between Fixtures | 2.5' from Walls

Materials list

MaterialQuantityUnitNotes
6-Inch or 4-Inch LED Slim Wafer Can Lights (800 Lumens)16FixturesSelectable CCT (3000K Warm / 4000K Neutral)
14/2 NM-B Romex Electrical Cable217FeetDaisy-chained between recessed fixture junction boxes
Single-Pole LED Digital Dimmer Switch1DimmerFlicker-free phase dimming for optimal light control

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$397 – $635

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$1,520 – $2,320

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,280

Average trade labor savings if executed as a skilled DIY homeowner project.

IESNA Zonal Lumen & Spacing Ratio Formula

Rendering formula...

IES Illuminance Math for 20' × 15' kitchen

  1. Room Area = 20 ft × 15 ft = 300 sq ft.
  2. Target Illuminance = 40 Foot-Candles for kitchen.
  3. Total Lumens Required = 300 sq ft × 40 fc = 12,000 lumens.
  4. Can Count: 12,000 ÷ 800 lumens/can = 15.0 → 15 minimum, rounded up to a full 4 × 4 grid = 16 fixtures.
  5. Recommended Grid Spacing: 4 rows × 4 columns spaced 5.0 ft apart (2.5 ft from walls).
Tip: 5.0 ft spacing is within the common ceiling-height ÷ 2 guide (4.5 ft for a 9-ft ceiling). Keep cans at least 18 inches from ceiling fan blades.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Room SizeRoom TypeTotal LumensRecessed Fixture Count (850 lm)Turnkey Electrical Install
12' × 14' (168 sq ft)Bedroom (20 fc)3,360 Lumens4 Fixtures (2×2 Grid)$450 – $750
15' × 20' (300 sq ft)Kitchen (40 fc)12,000 Lumens12 to 14 Fixtures (3×4)$1,200 – $1,900
16' × 22' (352 sq ft)Living Room (25 fc)8,800 Lumens8 to 10 Fixtures (2×4)$950 – $1,500
24' × 24' (576 sq ft)Workshop (60 fc)34,560 Lumens16 to 20 Fixtures (4×4)$1,800 – $2,800
NEC Section 410.116 / ASTM E283 Air-Tight Compliance

NEC 410 & IC-Rated Air-Tight Fixture Standards

Recessed luminaires installed in insulated ceilings must be Type IC (Insulation Contact) certified. In energy-code jurisdictions (IECC), fixtures must be tested per ASTM E283 to restrict conditioned air leakage into unconditioned attics.

How to use the recessed lighting calculator

  1. Enter your room dimensions (length and width in feet) to calculate the floor footprint and total area.
  2. Select your ceiling height (8, 9, 10, or 12 feet) to evaluate downlight beam spread and vertical light throw.
  3. Choose your room type (living room, kitchen, bathroom, or workshop) to apply the calculator's target foot-candle brightness level.

How many recessed lights do I need?

To determine how many recessed lights a room needs, calculate the room square footage, multiply by the recommended foot-candles (lumens per square foot) for that space, and divide by the lumen output of each fixture (typically 800 lumens for a standard 4-inch or 6-inch LED slim wafer downlight).

Room Area (sq ft) = Room Length (ft) × Room Width (ft)
Total Lumens Required = Room Area (sq ft) × Target Foot-Candles
Fixture Count = Total Lumens Required ÷ 800 Lumens per Fixture (rounded to the nearest whole fixture, minimum 4, then rounded up to fill an even grid)

For example, an 18×14 kitchen encompasses 252 square feet. Food preparation requires 40 foot-candles, yielding 10,080 total lumens (252 × 40). Dividing 10,080 lumens by 800 lumens per can results in 12.6, which rounds to 13 fixtures (minimum), then rounds up to fill an even 4×4 grid of 16 recessed lights.

Our calculator estimates the following costs for a 16-light kitchen installation:

  • DIY Materials ($397 – $635): 16 canless LED wafer fixtures, 217 feet of 14/2 NM-B Romex copper cable daisy-chained between junction boxes, and 1 single-pole LED digital dimmer switch.
  • Turnkey Professional Installation ($1,520 – $2,320): Licensed electrical contractor labor, circuit connection, drywall ceiling cutouts, cable fishing, and dimmer trim-out ($95 to $145 per fixture installed).

Recessed lighting spacing

A reliable rule of thumb spaces recessed can lights at approximately half the ceiling height apart. For an 8-foot ceiling, space fixtures roughly 4.0 feet apart; for a 9-foot ceiling, space fixtures 4.5 feet apart; and for a 10-foot ceiling, space fixtures 5.0 feet apart. Spacing from the perimeter walls should measure roughly half the fixture spacing (typically 2.0 to 2.5 feet from the wall).

Ceiling HeightRule-of-Thumb SpacingPerimeter Wall SpacingRecommended Room Applications
8 Feet4.0 ft between fixtures2.0 ft from wallBedrooms, standard living rooms, finished basements
9 Feet4.5 ft between fixtures2.3 ft from wallKitchens, primary suites, family rooms
10 Feet5.0 ft between fixtures2.5 ft from wallGreat rooms, open kitchens, 10-ft dining spaces
12 Feet6.0 ft between fixtures3.0 ft from wallVaulted ceilings, two-story entries, commercial lofts

As ceiling height increases, downlight cones broaden before reaching the floor, but illuminance at working surfaces drops rapidly due to the inverse-square law of light. For ceilings 10 feet and higher, choosing fixtures with narrower beam reflectors or higher lumen packages ensures light reaches task surfaces without creating excessive side glare.

Can light layout for common rooms

A balanced recessed lighting plan arranges fixtures in a symmetric rectangular grid across the ceiling. Spacing between fixtures along the length of the room is calculated as room length divided by the number of fixture columns, while wall distance equals half the fixture-to-fixture spacing.

Room DimensionsFloor AreaRoom PurposeTarget IlluminanceTotal LumensCan Count (800 lm)Grid Layout & SpacingDIY MaterialsTurnkey Pro InstalledNotes
10×12 ft120 sq ftLiving Room20 Foot-Candles2,400 lm4 Cans2×2 grid (6.0 ft apart, 3.0 ft from walls)$133 – $215$380 – $580Spacing wider than 4-ft guide for 8-ft ceiling — calculator flags this
12×12 ft144 sq ftLiving Room20 Foot-Candles2,880 lm4 Cans2×2 grid (6.0 ft apart, 3.0 ft from walls)$133 – $215$380 – $580Spacing wider than 4-ft guide for 8-ft ceiling — calculator flags this
16×12 ft192 sq ftKitchen40 Foot-Candles7,680 lm12 Cans3×4 grid (4.0 ft apart, 2.0 ft from walls)$309 – $495$1,140 – $1,740Spacing within 4.5-ft guide for 9-ft ceiling
18×14 ft252 sq ftKitchen40 Foot-Candles10,080 lm16 Cans4×4 grid (4.5 ft apart, 2.3 ft from walls)$397 – $635$1,520 – $2,320Spacing matches 4.5-ft guide for 9-ft ceiling
22×16 ft352 sq ftLiving Room20 Foot-Candles7,040 lm9 Cans3×3 grid (7.3 ft apart, 3.6 ft from walls)$243 – $390$855 – $1,305Spacing wider than 4-ft guide for 8-ft ceiling — calculator flags this
24×24 ft576 sq ftWorkshop / Garage60 Foot-Candles34,560 lm49 Cans7×7 grid (3.4 ft apart, 1.7 ft from walls)$1,123 – $1,790$4,655 – $7,105Spacing within 5-ft guide for 10-ft ceiling

When planning a kitchen layout, position the perimeter row directly above the front edge of kitchen countertops. If can lights are placed directly behind where you stand, your head and shoulders cast dark working shadows over cutting boards and sinks.

4″ vs 6″ cans

Both 4-inch and 6-inch recessed downlights provide effective illumination, but they serve different aesthetic and optical purposes:

  • 4-Inch Recessed Cans: Preferred for modern architectural designs, minimalist ceilings, and dedicated task lighting. A 4-inch aperture creates a subtle, unobtrusive ceiling appearance. They excel over kitchen islands, breakfast bars, bathroom vanity walkways, hallways, and accent art displays, casting a tighter beam pattern for focused task surfaces.
  • 6-Inch Recessed Cans: The traditional residential standard for general ambient illumination. The wider 6-inch trim casts a broader, softer wash of light across the floor, reducing harsh shadows in large open rooms. They are well-suited for high ceilings (9 to 12 feet), spacious living rooms, game rooms, and finished basements.
  • Canless LED Wafers: Modern ultra-slim wafer fixtures (available in both 4-inch and 6-inch diameters) have become common for residential retrofits. They snap directly into drywall with spring-loaded clips, connect to an included remote junction box, and can be installed directly beneath ceiling joists without cutting structural lumber.

Lumens per room type

Recommended lighting levels vary significantly based on how a room is used. Our calculator uses these target illuminance levels in foot-candles (one foot-candle equals one lumen per square foot):

Room TypeTarget IlluminanceLumens Required per Sq FtLighting Purpose & Design Priority
Living Room20 Foot-Candles20 Lumens / sq ftSoft ambient relaxation, reading nooks, and television viewing
Kitchen40 Foot-Candles40 Lumens / sq ftFood prep, knife safety, surface cleanliness, and recipe reading
Bathroom50 Foot-Candles50 Lumens / sq ftMirror grooming, makeup application, and wet shower stall clarity
Workshop / Utility60 Foot-Candles60 Lumens / sq ftHand and power tool safety, mechanical assembly, and storage sorting

Installing digital dimmer switches on every recessed lighting circuit is recommended. Dimmers allow you to run fixtures at full 100 percent output for task work or cleaning, then adjust brightness down for evening ambient relaxation.

Frequently asked questions

How far from the wall should recessed lights be?

Place recessed lights approximately half the distance between fixtures away from the wall. For example, if your layout spaces cans 4.5 feet apart, place the outside perimeter row roughly 2.3 feet from the wall. This spacing distributes light evenly across wall art and vertical surfaces while preventing intense scalloped bright spots or dark perimeter shadows. Keep fixtures at least 18 inches away from ceiling fan blades to prevent strobing shadows across the room.

How many lights on one 15-amp circuit?

Under the National Electrical Code (NEC / NFPA 70), a standard 15-amp 120-volt branch circuit supports up to 1,800 watts total capacity, with an 80 percent continuous load limit of 1,440 watts. Because modern 800-lumen LED can lights typically draw roughly 10 to 12 watts each (check the fixture's wattage label), a dedicated 15-amp lighting circuit could theoretically power over 100 LED fixtures (1,440 watts ÷ 12 watts = 120 fixtures). In practice, lighting circuits are shared with switches and other room devices, so check the label and your local electrical code for circuit load requirements.

Do I need IC-rated cans?

Yes, whenever the ceiling contains or directly touches thermal insulation. Under International Residential Code Chapter 40 (Section E4004) and NEC Section 410.116, luminaires installed in contact with combustible insulation must be certified as Type IC (Insulation Contact). Non-IC fixtures require a minimum 3-inch clearance from all insulation to prevent heat buildup and fire hazards. Many canless LED wafer downlights are IC-rated and airtight under ASTM E283 — check the product label and manufacturer specification sheet.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.