Epoxy Garage Floor Calculator

A 576 sq ft two-car garage floor needs about 4.6 gallons of 100% solids epoxy basecoat, 2.3 gallons of primer, 3.3 gallons of clear topcoat and 86 pounds of flake for a full broadcast. The calculator sizes a professional-grade system, not a store-bought kit.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(sq ft)
sq ft

Commercial Epoxy & Polyaspartic Kit

4.8 Gal 100% Solids Basecoat (600 sq ft)

Primer, Flake & Clear Topcoat

2.4 Gal Primer | 90 lbs Flake | 3.4 Gal Polyaspartic

Want a real price for this epoxy garage floor calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
100% Solids Moisture Vapor Barrier Epoxy Basecoat4.8Gallons12-15 mils dry film build without shrinkage
100% UV-Stable Polyaspartic High-Gloss Clear Topcoat3.4GallonsResists hot tire pickup and chemical spills
Decorative Vinyl Color Flake (full)90PoundsBroadcast into wet basecoat to rejection
Deep Penetrating Epoxy Concrete Primer2.4GallonsAnchors coating into mechanically ground CSP 2 pores

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$1,421 – $1,720

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$3,300 – $5,100

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$2,630

Average trade labor savings if executed as a skilled DIY homeowner project.

Epoxy Spread Rate & Dry Film Thickness (DFT)

Rendering formula...

Chemical Coverage Math for 600 sq ft Garage Floor

  1. Surface Area = 600 sq ft.
  2. 100% Solids Epoxy Basecoat (125 sq ft/gal spread) = 600 ÷ 125 = 4.8 gallons.
  3. Decorative Flake (0.15 lb/sq ft, full broadcast) = 90 pounds.
  4. Polyaspartic Clear Topcoat (175 sq ft/gal spread) = 600 ÷ 175 = 3.4 gallons.
Tip: In National Average, test concrete for moisture vapor emissions before coating. Acid etching fails on sealed concrete—diamond grinding to CSP 2 is required.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Garage SizeFloor AreaBase Epoxy GallonsColor Flakes (Full Broadcast)Pro Turnkey Install Price
1-Car Bay250 – 300 sq ft2.0 Gallons40 – 45 lbs$1,500 – $2,200
2-Car Bay500 – 600 sq ft4.0 Gallons80 – 90 lbs$2,800 – $4,200
3-Car Bay750 – 900 sq ft6.0 Gallons120 – 135 lbs$4,200 – $6,300
4-Car / Workshop1,000 – 1,200 sq ft8.0 Gallons150 – 180 lbs$5,500 – $8,400
ICRI Guideline No. 310.2R / SSPC-SP 13 Surface Preparation

ICRI Concrete Surface Profile (CSP) Guidelines

Concrete must test below 3 lbs/1,000 sq ft/24hr moisture vapor emission (ASTM F1869 Calcium Chloride test). Acid etching is insufficient for 100% solids coatings; concrete must be mechanically shot-blasted or diamond-ground to a CSP 2–3 texture.

How to use the epoxy floor calculator

  1. Enter the garage floor area in square feet. A two-car garage is often 400 to 600 square feet.
  2. Pick the flake coverage: light, medium or full broadcast.
  3. Read the gallons of primer, basecoat and topcoat and the pounds of flake, then compare the contractor range with your quotes.

How much epoxy do I need for a garage floor?

Divide the floor area by the coverage per gallon of each coat. Our calculator uses 250 square feet per gallon for primer, 125 for a 100% solids epoxy basecoat and 175 for the clear topcoat. Add up the coats and the flake.

Primer = Area ÷ 250    Basecoat = Area ÷ 125    Topcoat = Area ÷ 175

For 576 sq ft: primer 2.3 gallons, basecoat 4.6 gallons, topcoat 3.3 gallons.

FloorAreaBasecoatPrimerTopcoatFlake
1-car, medium flake264 sq ft2.1 gal1.1 gal1.5 gal24 lb
2-car, full flake576 sq ft4.6 gal2.3 gal3.3 gal86 lb
3-car, full flake768 sq ft6.1 gal3.1 gal4.4 gal115 lb

Flake is counted at 0.15 pounds per square foot for a full broadcast, 0.09 for medium and 0.03 for light.

How does a store-bought kit compare?

Retail kits cover much less per gallon than a professional 100% solids system. Quikrete's water-based two-part kit, for example, covers 220 to 280 square feet per kit, depending on how porous the concrete is, and it lists a one-car garage at about 240 square feet and a two-car garage at about 420. That is a thin coating. The calculator on this page is for the thicker professional-style system, so do not use its gallons to buy a store-bought kit. Buy by the coverage printed on the kit.

What preparation does the floor need?

Quikrete's data sheet says new concrete and concrete repairs must be cured for 30 days, the surface must be clean and etched or prepared as the maker directs, and the product should not be applied if temperatures outside 50 to 90°F are expected within 24 hours. It lists light foot traffic the next day and drive-on after 3 days. Professional systems usually grind the floor, and a moisture test is also common practice. The calculator's primer line assumes a ground floor. Follow the data sheet of the product you buy, because prep is the main reason these floors fail.

Frequently asked questions

How much does an epoxy garage floor cost?

For the 576 sq ft example the calculator shows about $1,366 to $1,654 in materials if you apply it yourself, and $3,168 to $4,896 with a contractor, at national averages. That is $5.50 to $8.50 per square foot installed.

How much flake do I need?

A full broadcast covers the floor until the basecoat is saturated and the excess is swept up. The calculator's figure is 86 pounds for 576 sq ft. Flake sold in boxes and bulk varies, so check the coverage on the product and buy a little extra.

Does the DIY water-based option change the numbers?

Not in this calculator. The system type selector does not change the quantities, which are for a 100% solids epoxy with a clear topcoat. Water-based kits are thinner and sold by the kit, so use the coverage on the box.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.