Epoxy Resin Calculator

A river table mold that is 48 × 10 inches and 1.75 inches deep holds 3.82 gallons of epoxy once you add 5% for mixing loss. At a 2:1 ratio that is 2.55 gallons of resin and 1.27 gallons of hardener.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(inches)
inches
(inches)
inches
(inches)
inches
(%)
%

Total Deep-Pour Epoxy Required

3.93 Gallons (502.6 Fluid Ounces)

Mix Ratio Component Breakdown

Part A Resin: 2.62 Gal • Part B Hardener: 1.31 Gal (2:1 Ratio)

Materials list

MaterialQuantityUnitNotes
Deep-Pour Casting Epoxy Resin (Part A)2.62GallonsLow-viscosity high-clarity resin component
Epoxy Hardener / Catalyst (Part B)1.31GallonsSlow-cure catalyst formulation (ASTM D2471)
Polypropylene Mold Release Tape & Spray1KitSeals mold form and prevents resin adhesion to melamine

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$413 – $496

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$1,100 – $1,886

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,039

Average trade labor savings if executed as a skilled DIY homeowner project.

Thermoset Stoichiometric Volume & Displacement Formula

Rendering formula...

Resin Volume & Mix Derivation for 48" L × 12" W × 1.5" Depth

  1. Total Mold Cavity Volume = 48" × 12" × 1.5" = 864.0 cubic inches.
  2. Adding 5% mixing loss: 907.2 cubic inches.
  3. Fluid Ounces = 907.2 / 1.805 = 502.6 fl oz (3.93 US Gallons).
  4. Apportioning 2:1 mix ratio: Part A = 2.62 gal, Part B = 1.31 gal.
Tip: Maintain room temperature between 68°F and 72°F during cure to prevent runaway thermal boiling.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Project DimensionsCubic InchesTotal Fluid OuncesTotal GallonsPart A : Part B (2:1 Ratio)
18" × 6" × 0.75" (Board)81 cu in0.37 Gallons47 fl oz31 oz Resin : 16 oz Hardener
36" × 10" × 1.5" (Small)540 cu in2.45 Gallons314 fl oz209 oz Resin : 105 oz Hardener
48" × 12" × 1.75" (River)1,008 cu in4.58 Gallons586 fl oz391 oz Resin : 195 oz Hardener
72" × 16" × 2.0" (Dining)2,304 cu in10.47 Gallons1,341 fl oz894 oz Resin : 447 oz Hardener
ASTM D2471 Gel Time and Peak Exothermic Temperature of Reacting Thermoset Resins

ASTM D2471 / D1475 Epoxy Gel Time & Density Standards

Deep-pour formulations must strictly respect maximum single-pour thickness limits (typically 2 to 3 inches) to avoid runaway thermal exotherm (boiling, yellowing, or cracking). Room temperature must be maintained between 68°F and 75°F.

How to use the epoxy resin calculator

  1. Enter the length and width of the mold in inches, and the depth you plan to pour.
  2. Choose the mix ratio from your product's label: 1:1, 2:1 or 3:1 by volume.
  3. Read the total volume and the amount of Part A and Part B, then check your product's maximum pour depth before you pour.

How much resin do I need?

Multiply length × width × depth in inches to get cubic inches, add a little for the resin that sticks to cups and sticks, and convert to fluid ounces. One US fluid ounce is 1.805 cubic inches, and a gallon is 128 fluid ounces. Our calculator adds 5%.

Cubic inches = Length × Width × Depth × 1.05
Fluid ounces = Cubic inches ÷ 1.805
Gallons = Fluid ounces ÷ 128

For 48 × 10 × 1.75 in: 840 cu in × 1.05 = 882, ÷ 1.805 = 488.6 fl oz = 3.82 gallons.

ProjectSizeRatioTotalPart APart B
River table48 × 10 × 1.75 in2:13.82 gal2.55 gal1.27 gal
Coffee table36 × 14 × 1.5 in2:13.44 gal2.29 gal1.15 gal
Charcuterie board24 × 6 × 0.75 in2:10.49 gal0.33 gal0.16 gal
Bar top flood coat72 × 24 × 0.125 in1:10.98 gal0.49 gal0.49 gal

If your mold is not a box, work out its volume another way, or fill it with water or rice and measure that.

What does the mix ratio mean?

A 2:1 ratio means two parts resin to one part hardener by volume, so a third of the mixed epoxy is hardener. A 1:1 ratio is half and half, and 3:1 is three parts resin to one part hardener. The ratio is printed on the product. Measure by volume or by weight exactly as the label says, because a wrong ratio can leave the epoxy tacky.

How deep can I pour epoxy in one layer?

It depends on the product, and the limit is on the label. One deep-pour epoxy is rated for 2 inches at most in one pour, and its maker says to wait 12 hours before pouring the next layer, keeping each extra layer to about an inch. The same maker limits its bar and table top epoxy to 1/8 inch. Pouring thicker than the limit risks air bubbles and incomplete curing. For the 1.75 inch river table, a 2 inch product can take it in one pour, and a thinner product needs several layers. The calculator totals the whole volume, so buy for all layers.

Frequently asked questions

How much does epoxy resin cost?

The calculator uses about $105 per gallon for the kit, which gives $401 to $481 for the river table. A professional charge for the same piece is shown at $1,070 to $1,834. Deep-pour resin prices vary by brand, so check the price of your product.

Should I buy extra?

Yes. Resin that sticks to mixing cups and sticks, a mold that is not perfectly level and a second pour to fix a flaw all use more. The calculator adds 5%, and some makers add more for tricky molds. A small extra batch is cheaper than running short mid-pour.

Is this for epoxy floors?

No. This page is for casting and coating resin by volume. For a garage floor coating, use the epoxy garage floor calculator, which works by square feet.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.