EPDM Roof Calculator

A 24 × 24 ft flat garage roof with a 12-inch wall up-turn needs 676 sq ft of 60-mil EPDM, which fits on one 10 × 100 ft roll, plus about 12 gallons of bonding adhesive. Installed, our calculator puts it at $5,070 to $8,112.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(ft)
ft
(ft)
ft
(in)
in

Total 60-Mil EPDM Rubber Membrane

1 Rolls (704 sq ft needed)

Bonding Adhesive & Seam Tape

12 Gal Adhesive | 69 ft Seam Tape

Want a real price for this epdm roof calculator project?

Get up to 3 free quotes from local contractors. No obligation. Your numbers are included.

Materials list

MaterialQuantityUnitNotes
60-Mil Commercial EPDM Membrane (10'×100')1RollsAccounts for 12" parapet up-turn and 6" factory seams
Solvent-Based EPDM Bonding Adhesive12GallonsContact adhesive rolled onto both substrate and rubber back
6-Inch Cured Double-Sided Seam Tape69Linear FeetRoll-pressed with 2-in steel roller to activate butyl seal
EPDM Seam Primer & Activator1GallonsApplied with scrub pad before seam tape placement
Aluminum Parapet Termination Bar100Linear FeetMechanical anchor fastening at wall flashing tops

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$2,089 – $2,529

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$5,280 – $8,448

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$4,555

Average trade labor savings if executed as a skilled DIY homeowner project.

EPDM Surface Area & Adhesive Coverage Calculations

Rendering formula...

EPDM Specification Math for 30' × 20' Deck with 12" Up-Turn

  1. Gross Dimensions (inc. 12" up-turns) = (30' + 2×1.00') × (20' + 2×1.00') = 32.0' × 22.0' = 704 sq ft.
  2. 10'×100' Rolls (900 net sq ft after 6" seam overlaps) = 704 ÷ 900 = 0.78 → 1 rolls.
  3. Bonding Adhesive: 704 sq ft ÷ 60 sq ft/gal two-sided coverage = 12 gallons.
  4. Seam Tape: 0 longitudinal seams + parapet details = 69 linear feet.
Tip: In National Average, roof deck must be completely dry and polyiso insulation joints taped prior to adhesive application to prevent blister formation.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Roof DimensionsMembrane Area60-mil Membrane RollsBonding Adhesive (Gal)Contractor Turnkey Price
12' × 16' Addition (12" up-turn)252 sq ftOne 10' × 100' Roll5 Gallons$1,890 – $3,024
20' × 24' Garage (12" up-turn)572 sq ftOne 10' × 100' Roll10 Gallons$4,290 – $6,864
25' × 40' Flat Roof (12" up-turn)1,134 sq ftTwo 10' × 100' Rolls19 Gallons$8,505 – $13,608
30' × 60' Flat Roof (12" up-turn)1,984 sq ftThree 10' × 100' Rolls34 Gallons$14,880 – $23,808
IRC 2024 Section R905.12 / ASTM D4637 Type I

ASTM D4637 & IRC R905.12 Membrane Standards

Low-slope EPDM systems require minimum design positive slope of 1/4" per foot (2%) to internal drains or scuppers. Substrate boards (polyisocyanurate insulation or high-density fiberboard) must be mechanically fastened with approved 3" insulation plates.

How to use the epdm roof calculator

  1. Enter the roof's length and width in feet, measured to the outside edges of the deck.
  2. Enter the parapet or wall up-turn in inches. The membrane runs up that wall, so it adds to the area you buy.
  3. Pick the membrane thickness. The result shows rolls, adhesive, seam tape, termination bar and an installed price range.

How much does an EPDM roof cost?

Our calculator prices installed EPDM at $7.50 to $12.00 per square foot of membrane, including the up-turns. That works out to the totals below for three common flat roofs:

RoofMembrane areaRolls (10 × 100 ft)AdhesiveInstalled cost
16 × 14 ft sunroom, 6" up-turn255 sq ft15 gal$1,913 – $3,060
24 × 24 ft garage, 12" up-turn676 sq ft112 gal$5,070 – $8,112
40 × 30 ft flat bay, 18" up-turn1,419 sq ft224 gal$10,643 – $17,028

Doing it yourself, the materials for the garage roof come to $2,086 to $2,525. Tear-off of an old roof, new insulation board and any rotten decking are extra, so get a written quote that lists them.

How many rolls of EPDM do I need?

Add twice the up-turn height to the length and to the width, multiply, and divide by the usable area of a roll. Our calculator counts 900 sq ft per 10 × 100 ft roll, because seams overlap by about 6 inches. A 40 × 30 ft roof with 18-inch up-turns becomes 43 × 33 ft, or 1,419 sq ft, which is 1.58 rolls, so you buy 2.

How much EPDM adhesive per square foot?

Bonding adhesive is rolled onto both the deck and the back of the rubber, so it goes about half as far as you might expect. Our calculator uses 60 sq ft per gallon of finished roof. The 676 sq ft garage roof needs 12 gallons; buy it in the same batch so the drying time is consistent.

Frequently asked questions

Is 60-mil or 45-mil EPDM better?

60-mil is the common choice for homes because it is thicker and more forgiving of foot traffic and hail. 45-mil costs less and suits small, low-traffic roofs such as sheds. Our calculator lets you switch between 45, 60 and 90-mil so you can compare.

Can I install EPDM myself?

Many homeowners do on small, simple roofs, since the rubber goes down in one sheet with few seams. Seams, corners and drains are where leaks start, so a garage or sunroom with several penetrations is often worth handing to a roofer.

Does an EPDM quote include tear-off?

Not always. Ask whether the price covers removing the old roof, replacing damaged decking, new cover board or insulation, and edge metal. Those items can move the total more than the membrane itself.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.