Stair Calculator

Calculate residential stair rise, run, and stringer cuts matching International Residential Code (IRC) limits. For a standard 9-foot floor height (108-inch rise), a code-compliant staircase requires 14 risers at 7.71 inches each and 13 treads with 136.5 inches of horizontal run.

Free · No sign-up · Last reviewed

Quick start:

Your project size

(inches)
inches
(inches)
inches
(inches)
inches
(inches)
inches

Stair Flight: 14 Risers @ 7.71" Each

14 Risers / 13 Treads Exact Riser: 7.71" (Max 7.75" Code)

Horizontal Run & Stringer Geometry

Total Run: 136.5" (11.4 ft) • Slope Angle: 36.3° (3 Stringers)

Materials list

MaterialQuantityUnitNotes
2×12 Cut Stringer Lumber (16-Ft Stock)32x12 BoardsRequires 16-ft boards for 174" diagonal hypotenuse
Bullnose Stepping Treads (1-1/16" × 11-1/2")13Tread Boards36" wide stepping surface (IRC R311.7.5.2)
Riser Facing Trim Boards (3/4" × 8")14Riser BoardsVertical riser face closure
Heavy-Duty Stringer Hanger Brackets3BracketsSimpson Strong-Tie LSCZ adjustable stringer hangers

Estimated cost: DIY vs. contractor

National Average
DIY Raw Materials Only
$756 – $945

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Hired contractor
$1,960 – $3,640

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$1,950

Average trade labor savings if executed as a skilled DIY homeowner project.

Blondel's Architectural Stair Rule & IRC R311.7 Code

Rendering formula...

IRC R311.7 Code Stair Derivation for 108" Total Rise

  1. Riser count: round(108" / 7.5") = 14, at least ceil(108" / 7.75") = 14 to stay within the IRC maximum → 14 risers.
  2. Exact Riser Height: 108" / 14 = 7.714" (IRC maximum is 7.75").
  3. Tread Count: 14 risers - 1 = 13 treads.
  4. Total Horizontal Run: 13 × 10.5" tread depth = 136.5" (11.38 ft).
  5. Stringer cut diagonal: sqrt(108² + 136.5²) = 174" (16-ft 2x12 stock required).
Tip: Verify clear vertical headroom of at least 80 inches (6' 8") measured vertically from the tread nosing line.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Total Floor RiseRiser CountExact Riser HeightTotal Horizontal RunStringer 2x12 Length
36 Inches (Deck)5 Risers7.20 Inches42.0 Inches (3.5 ft)6-Ft 2x12 Stock
72 Inches (Porch)10 Risers7.20 Inches94.5 Inches (7.9 ft)12-Ft 2x12 Stock
96 Inches (8-Ft)13 Risers7.38 Inches126.0 Inches (10.5 ft)14-Ft 2x12 Stock
108 Inches (9-Ft)14 Risers7.71 Inches136.5 Inches (11.4 ft)16-Ft 2x12 Stock
International Residential Code (IRC 2024) Section R311.7

IRC R311.7 Stairway Safety & Geometry Standards

Maximum riser height is 7-3/4 inches (196 mm). Minimum tread run is 10 inches with 3/4-inch to 1-1/4-inch nosing (or 11 inches without nosing). The greatest riser height in any flight shall not exceed the smallest by more than 3/8 inch. Minimum headroom clearance is 6 feet 8 inches (80 inches).

How to use the stair calculator

  1. Measure vertical total rise from the finished lower floor surface to the finished upper landing surface.
  2. Enter your target riser height (7.5 inches default; 7.75 inches maximum under IRC) and preferred tread depth (minimum 10 inches).
  3. Review step counts, exact unit riser and run cuts, stringer board length, and total horizontal stair run.

How to calculate stairs

To calculate stairs, divide your vertical total rise in inches by 7.75 (the maximum IRC residential riser height) and round up to find your riser count. Divide total rise by this riser count to get your exact unit riser height. Next, subtract 1 from the riser count to determine the number of stepping treads.

The primary formulas for stair geometry follow standard residential carpentry principles:

  • Riser Count = total rise ÷ 7.75, rounded up to the nearest whole integer
  • Exact Unit Riser Height = total rise ÷ riser count
  • Tread Count = riser count - 1
  • Total Horizontal Run = tread count × tread depth

Consider a full worked example for a two-story home with a 108-inch floor-to-floor vertical rise:

  1. Divide rise by code limit: 108 ÷ 7.75 = 13.93. Rounding up gives 14 risers.
  2. Calculate unit riser height: 108 ÷ 14 = 7.714 inches (compliant with the 7.75-inch code ceiling).
  3. Determine stepping treads: 14 - 1 = 13 treads.
  4. Calculate horizontal stair run using a standard 10.5-inch tread depth: 13 × 10.5 = 136.5 inches (11.38 feet).

How to measure total rise and run

Total rise is the exact vertical distance from the finished surface of the lower floor to the finished surface of the upper floor or deck. Never measure rough subfloor to rough subfloor without accounting for flooring thickness (tile, hardwood, underlayment). Total run is the available horizontal space along the floor from the top landing plumb line to the bottom riser face.

To measure total rise on a jobsite:

  • Drop a plumb line or set a self-leveling cross-line laser from the edge of the upper floor opening down to the lower level.
  • Measure vertically with a steel tape measure from the laser reference point to the final finished floor height.
  • Account for finish flooring material offsets. If the upper floor receives 3/4-inch solid hardwood while the basement floor remains bare concrete, add that 3/4 inch to your vertical rise measurement.

When cutting the bottom of the wood stringer, perform the "bottom riser deduction." Trim off the thickness of one tread (typically 1-inch or 1-1/16-inch bullnose tread) from the bottom of the stringer. Without this cut, the bottom step would end up one tread thickness too tall, and the top step would end up one tread thickness too short, violating code consistency.

How long should a stair stringer be?

To find stair stringer length, apply the Pythagorean theorem using total vertical rise and total horizontal run: Stringer Length = square root of (Total Rise² + Total Run²). For a 108-inch rise with a 136.5-inch run, the diagonal hypotenuse equals 174.1 inches (14.5 feet). You must purchase a 16-foot 2×12 lumber board to cut the stringer without splicing, because dimension lumber is stocked in even two-foot increments.

Stair stringers must be cut from solid 2×12 structural framing lumber (No. 2 Southern Pine or Douglas Fir). Never use 2×10 lumber for cut stringers. When you cut notches for a 7.5-inch rise and a 10.5-inch run into a 2×10 board, the remaining uncut timber along the bottom edge—known as the stringer throat—measures about 3 inches, which is below the 5-inch minimum throat required for cut stringers in guides such as AWC DCA 6. A 2×12 leaves a solid throat of roughly 5 inches, providing adequate structural stiffness.

Total Rise (Height)Horizontal Run (10.5″ Treads)Diagonal HypotenuseMinimum Stringer Board StockStringers Needed (36″ Stair)
36 inches (5 risers)42.0 in (3.5 ft)55.3 in (4.6 ft)8-Foot 2×123 Boards
48 inches (7 risers)63.0 in (5.3 ft)79.2 in (6.6 ft)8-Foot 2×123 Boards
60 inches (8 risers)73.5 in (6.1 ft)94.9 in (7.9 ft)8-Foot 2×123 Boards
72 inches (10 risers)94.5 in (7.9 ft)118.8 in (9.9 ft)10-Foot 2×123 Boards
84 inches (11 risers)105.0 in (8.8 ft)134.5 in (11.2 ft)12-Foot 2×123 Boards
96 inches (13 risers)126.0 in (10.5 ft)158.4 in (13.2 ft)14-Foot 2×123 Boards
108 inches (14 risers)136.5 in (11.4 ft)174.1 in (14.5 ft)16-Foot 2×123 Boards
120 inches (16 risers)157.5 in (13.1 ft)198.0 in (16.5 ft)18-Foot 2×123 Boards

Stair code limits at a glance

Residential stair construction in most US jurisdictions follows the International Residential Code (IRC Section R311.7). The code mandates a maximum riser height of 7¾ inches (7.75″) and a minimum tread depth of 10 inches (or 11 inches if no nosing overhang is provided). Riser heights and tread depths within a single flight of stairs cannot vary by more than ⅜ inch (0.375″).

Stairway dimensions exist to maintain natural human gait cadence. Irregular step heights cause occupants to stumble. Building inspectors measure individual risers and treads on final inspection, flagging variations over 3/8 inch as immediate safety hazards.

The key residential stair specifications under IRC R311.7 are summarized below:

IRC Code RequirementSectionSpecification LimitPractical Rule
Maximum Riser HeightR311.7.5.17¾ in (197 mm)Limits steep step climbs
Minimum Tread DepthR311.7.5.210 in (254 mm) with nosing, 11 in withoutProvides full foot contact when descending
Maximum Riser/Tread VariationR311.7.5.1 / 2⅜ in (9.5 mm) within any flightEliminates tripping hazards between steps
Minimum Clear WidthR311.7.136 in (914 mm) above handrailPermits clear passage and furniture clearance
Minimum Vertical HeadroomR311.7.26 ft 8 in (80 in / 2,032 mm)Measured vertically from plane of tread nosings
Handrail Height RangeR311.7.8.134 in to 38 in vertically from nosingsStandard ergonomic reach height
Handrail Grip Profile (Type I)R311.7.8.51¼ in to 2 in diameter circular, or perimeter 4–6¼ inPower grasp security during slip recovery

(Always check with your local municipal building department, as local amendments may adopt stricter riser maximums such as 7 inches in commercial or local codes).

Stair rise and step counts for common heights

The following table outlines calculated stringer geometries for floor-to-floor heights ranging from 24 inches to 120 inches. Riser counts are determined by dividing total rise by the 7.75-inch code limit and rounding up (risers = total rise ÷ 7.75, rounded up), paired with a standard 10.5-inch tread depth:

Total Rise (Height)Riser CountExact Unit Riser HeightTread Count (10.5″ Run)Total Horizontal RunStringer Cut LengthLumber Stock Required
24 inches (2 ft)4 risers6.00 in3 treads31.5 in (2.6 ft)39.6 in8-Ft 2×12
36 inches (3 ft)5 risers7.20 in4 treads42.0 in (3.5 ft)55.3 in8-Ft 2×12
48 inches (4 ft)7 risers6.86 in6 treads63.0 in (5.3 ft)79.2 in8-Ft 2×12
60 inches (5 ft)8 risers7.50 in7 treads73.5 in (6.1 ft)94.9 in8-Ft 2×12
72 inches (6 ft)10 risers7.20 in9 treads94.5 in (7.9 ft)118.8 in10-Ft 2×12
84 inches (7 ft)11 risers7.64 in10 treads105.0 in (8.8 ft)134.5 in12-Ft 2×12
96 inches (low basement / 8′ floor-to-floor)13 risers7.38 in12 treads126.0 in (10.5 ft)158.4 in14-Ft 2×12
102 inches (basement)14 risers7.29 in13 treads (10″)130.0 in (10.8 ft)165.2 in14-Ft 2×12
108 inches (9′ floor)14 risers7.71 in13 treads136.5 in (11.4 ft)174.1 in16-Ft 2×12
120 inches (10′ floor)16 risers7.50 in15 treads157.5 in (13.1 ft)198.0 in18-Ft 2×12

Frequently asked questions

How many steps for an 8-ft ceiling (~ 9 ft floor-to-floor)?

An 8-foot ceiling usually creates a finished floor-to-floor total rise of approximately 9 feet (106 to 110 inches) after including ceiling drywall, 2×10 or 2×12 floor joists, and upper subfloor plus finish flooring. For a standard 108-inch floor-to-floor rise, you need 14 risers at 7.71 inches each (13 stepping treads). For a 96-inch rise (such as an exterior grade drop or low basement opening), you need 13 risers at 7.38 inches each (12 treads).

What's the most comfortable stair angle?

Stair builders often reference the classic Blondel rule of thumb: 2 × Riser + Tread = 24 to 25 inches. Combining a 7.5-inch riser with a 10.5-inch tread produces 2 × 7.5 + 10.5 = 25.5 inches, which is slightly above the classic 25-inch threshold but remains standard in modern residential construction with a natural walking cadence.

How many stringers do I need for a 36″ stair?

A standard 36-inch wide stairway requires at least 3 stringers spaced roughly 18 inches on center (one on each outside edge plus a center support stringer, meeting the AWC DCA 6 guideline of 18 inches maximum on-center spacing for cut stringers). Using only two stringers across a 36-inch span causes stepping treads to bounce, creak, and deflect under load. Stairways wider than 36 inches require a 4th stringer.

Sources and review

Prices and quantities come from the calculator above. Last reviewed . How our calculators work.